Plumbing Basics: Your Key to Bathtub Installation
Plumbing Basics: Your Key to Bathtub Installation
Blog Article
The content in the next paragraphs relating to How to Install a Bathtub Yourself is immensely insightful. You should take a look.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a tub isn't precisely rocket science, but it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily accessible, the task can move speedily; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and set in the new one. See to it you have qualified on your own for the job as well as fit attempting it. Instead of hiring a professional to take control of a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you might need a specialist plumber to make tube links.
This write-up will certainly assist you install a brand-new tub in your shower room if you have actually already purchased a brand-new bathtub and do not need to change the setup of your previous water supply pipelines.
Your tools as well as material list should consist of the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid strain on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last setting.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome due to the limited gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before proceeding to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the tub till the level checks out degree.
To set up taps, fit all-time low of the furthest versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water and examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bathtub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it right into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in area between the faucet and also the sink. Secure the faucet in position with the producer offered backnut. As soon as the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous type ought to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall in between the bath as well as the tiling, leading to difficulties with wetness and possible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before securing, to allow for the activity experienced when the tub is in use. The sealant can fracture relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I have been very fascinated by How to Install a Bathtub and I am assuming you appreciated the article. Liked our posting? Please share it. Let somebody else check it out. I take joy in reading our article about Installing A Bathtub.
Ring, relax, resolved! Report this page